CR-10 & Tevo Tarantula Direct Drive Upgrade Kit – v1.2

$34.95

  • Easy to Install
  • No Modification Required
  • Better Routing of Filament

Out of stock

Description

This is a new and improved version of our previous Creality CR-10 Direct Drive Kit

Creality CR-10 Direct Drive

Creality CR-10 Direct Drive upgrade kit:

Increase print quality, simplify retractions and filament changes, and print any material with ease with the MDD v1.2, the easiest direct drive conversion kit available for your CR-10 3D printer.

Lighter than a Titan Aero or Bondtech, the MDD takes just 20-30 minutes to install– with no firmware changes, no printable volume loss, and no cutting or splicing required.

The MDD (or ”Modular Direct Drive”) easily converts your stock CR-10 into a true direct drive 3D printer. While the MDD is compatible with many different hot end and extruder combinations, it was specifically engineered to convert your stock components into a powerful direct drive system with no additional hardware or wiring needed, making it the simplest and most flexible direct drive system.

Ender 3 Version

There is also a version of this that will work on the Creality CR-10 and Tevo Tornado available here.

Ender 5 Version

If you have an Ender 5, you can purchase a kit designed specifically for the Creality Ender 5 here.

HIGHLIGHTS

  • Increase print quality and fix retraction issues
  • Does not require dual lead screws
  • Print higher temperature and flexible materials
  • Reduce retractions and ooze control
  • Easier filament changes
  • No firmware or bootloader flashing
  • No cutting or splicing wires
  • Works with stock extruder and hot end
  • Compatible with many printable mods

DIRECT DRIVE VS. BOWDEN TUBE EXTRUDERS

Bowden style extrusion systems like those found on Creality printers rely on long PTFE tubes to feed filament to the hot end, and as such are more prone to extrusion issues. While Bowden setups generally allow for lighter print head weights, mounting the extruder separately from the hot end comes at the expense of less precise retraction control and filament changes.

By contrast, direct drive extruders eliminate most common extrusion problems by mounting the extruder and hot end very closely together, removing the need for the PTFE tubing in between and drastically shortening and simplifying the filament path. While this approach can significantly improve extrusion and retraction, and allow for easier printing of difficult materials like flexible filaments, it also increases the weight on the hot end carriage, necessitating reduced print speeds if made too heavy.

MDD – A BETTER DIRECT DRIVE OPTION

Weighing in at 479g when installed with a full-sized stepper, the MDD is light enough to print fast, while solving many of the extrusion problems inherent to Bowden extruder systems. And because it entirely replaces the hot end carriage, it provides a vastly more rigid mounting platform for the extruder and hot end compared with printed direct drive mounts, which are more prone to vibration and ringing when printing at higher speeds.

Want to install this on a larger format machine than the CR-10 and larger?

All you need is one or more motor extension cables.

Hot end / Extruder Compatibility

Creality Mk8 E3D v6 / Lite6 Micro Swiss J-Head
Creality Mk10 (factory or aluminum) Spacer included STL(s) needed: V6 / J adapter Spacer included STL(s) needed: V6 / J adapter
Bondtech BMG STL(s) needed: BMG spacer, Mk8 J adapter, Mk8 fan duct STL(s) needed: BMG spacer STL(s) needed: BMG spacer, Mk8 J adapter, Mk8 fan duct STL(s) needed: BMG spacer
E3D Titan STL(s) needed: Titan 6mm spacer, Mk8 J adapter, Mk8 fan duct STL(s) needed: Titan 6mm spacer STL(s) needed: Titan 6mm spacer, Mk8 J adapter, Mk8 fan duct STL(s) needed: Titan 6mm spacer
SeeMeCNC EZR Struder™ STL(s) needed: EZR Struder spacer STL(s) needed: EZR Struder spacer, V6 / J adapter STL(s) needed: EZR Struder spacer STL(s) needed: EZR Struder spacer, V6 / J adapter

Technical Specs

  • CNC machined 6063 aluminum construction
  • Injection molded fittings – no 3D printed parts*
    • Printed or customized parts may be required to mount up certain combinations of non-factory or 3D printed components.
  • Weighs under 500g fully installed (including fan shroud, wiring, hardware)
  • Wire harness extender included
  • High-temp PTFE tube rated for 260ºC+
  • Simple 20 minute installation (instructions provided)

FAQ

Q: Is it too heavy? Do I need a dual Z lead screw?

A: No, a dual lead screw setup is not needed for the MDD, even when using a full-sized Creality stepper motor. Just a properly aligned X gantry (see this guide for more information: https://www.youtube.com/watch?v=4bFYH0X3qjk)

Our tests have demonstrated that the increased effector mass on the X axis is not heavy enough to cause significant unwanted deflection or drop, even higher than average travel speeds. This is partly due to the rigid coupling and alignment of the stepper motor with the MDD’s solid carriage plate, which restricts unwanted movements and vibrations, and effectively translates those forces to the rollers, which are more than strong enough to bear the load without deforming.

Q: Which Creality CR models is it compatible with?

A: The MDD will fit all CR models EXCEPT the CR-10S PRO.

For the Ender 5 version, click here.

For the Ender 3 version, click here.

Q: What hot ends and extruders does the MDD work with?

A: Many, though we recommend using it with the stock Creality hot end and extruder combination. Other supported components include extruders like the Bondtech BMG, E3D Titan and EZR Struder, as well as hot ends like the E3D V6 and Micro-Swiss, with more compatibility coming soon.

Q: What slicer settings do I need to change?

A: Slicer settings can vary based on machine, filament, etc. However, you should expect to significantly reduce your slicer retraction settings (we recommend starting around 1.0mm at 30mm/s and tuning from there). You will also need to disable ooze control methods like coasting, wipe, etc.

Q: Where does this product ship from?

A: We manufacture and produce our kits in the USA. All MDD kits purchased from Fargo 3D Printing ship from Fargo, ND in the USA.

Q: Does this upgrade have a mounting point for an auto-leveling system like the BL Touch?

A: YES. 

More Resources

Additional information

Weight 0.3 lbs
Dimensions 6 × 4 × 1 in
3D Printer Compatibility

, , , , ,

Join the waitlist to be emailed when this product becomes available

©2024 Fargo 3D Printing

Fargo 3D Printing is not associated with HID Global and their FARGO division.

LEGAL DISCLAIMER

THE PRODUCTS SOLD ON THIS WEBSITE SHOULD ONLY BE USED BY EXPERIENCED INDIVIDUALS, OR UNDER THE DIRECT SUPERVISION OF EXPERTS. NO WARRANTY OF THEIR SUITABILITY FOR ANY PURPOSE WHATSOEVER IS MADE OR OFFERED BY US. YOUR USE OF THE PRODUCTS SOLD ON THIS WEBSITE IS ENTIRELY AT YOUR OWN RISK. YOUR PURCHASE OR USE OF ANY PRODUCT HEREFROM SHALL SERVE AS YOUR EXPLICIT ACKNOWLEDGEMENT THAT YOU UNDERSTAND AND CONSENT TO THE FACT THAT WE HEREBY DISCLAIM ANY RESPONSIBILITY OR LIABILITY FOR, ANY HARM, LOSS (ECONOMIC OR OTHERWISE), INJURY OR DEATH RESULTING FROM THE ASSEMBLY OR OPERATION OF OUR PRODUCTS, EITHER AS INSTRUCTED OR OTHERWISE, AND AFFIRM THAT UNDER NO CIRCUMSTANCES SHALL YOU BE ENTITLED TO ANY DAMAGES OF ANY SORT WHATSOEVER RELATED TO YOUR USE OR MISUSE OF OUR PRODUCTS.

Log in with your credentials

Forgot your details?